Did you know?

Litter-Robot 3: Filling the Globe. Fill the Globe through the opening with clumping litter until it meets the raised Fill Line when spread flat (about 8-10 pounds by weight or 1 gallon by volume). Be careful not to overfill the Globe. Then press the Reset button. Litter-Robot's litter sifting system requires clumping litter to work properly.Find step-by-step instructions on Litter-Robot 3 motor installation. Easy, efficient, and user-friendly. ... locate the red and white wires and use the needle-nose pliers to lift them out of the wire channel. ... unit in, turn it on, and let the initial cycle finish The globe should return to the home position with the blue ready light on. If ...Litter-Robot 3 flashing red light. A solid crimson light on your Litter-Robot 3 govern panel means that the cat sensor was activated of your cat entering the spheres while one unit was ready to getting. The unit is counting blue to a cleanup cycle, depending on your set wait hours (3, 7, or 15 minutes).My litter robot is stuck on flashing red (1 per second). I know it's to do with the cat sensor saying there is too much weight. How do I fix it. The robot is on flat surface, not over full and clean. I have continuous problems with the unit. It is only 2.5 years old and already have had to change the tray sensor three times. I have tried to re set it but the light continues and it just won ...Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 …A fence comes standard with Litter-Robot 4, but you can also purchase a Litter-Robot 3 Fence that snaps on to the entrance of the Litter-Robot globe to promote your cat's full entry. The fence acts as a barrier to contain kicked-up litter and helps prevent those half-in, half-out messes. Plus, the Litter-Robot 3 Fence comes in four colors!Explore the Litter-Robot 4 Wifi Light Status help page to troubleshoot issues. Get step-by-step guidance and solutions. Click now for instant assistance.Came home to my Litter-Robot in the upside down position and the yellow flashing (2 flashes per second) and I cannot get the globe to turn at all to try to reset itself. There is power to the unit because the yellow light is flashing but regardless of which buttons I press or turn power on/off no movement of the unit can be made. I have cleaned and emptied the unit and even reset the spring in ...Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more.The Litter-Robot is ready for use when the Globe is at the Home position and the blue light on the Control Panel is on. x When a cat enters the Globe, the Cat Sensor is activated; the blue light turns off and the red light turns on. x Once the cat exits the Globe, the countdown to a Clean cycle begins. When the Wait Time (see page 23) hasReboot your router. Completely close the Litter-Robot app. While the unit is at the Home position with the solid blue light, unplug your unit from the BASE, not the wall. Wait 15 seconds, plug it back in, and allow it to cycle until the solid blue light comes on ("Ready" status). Open the app and follow the steps.Take the bonnet and globe off, replace on the base the bonnet ONLY. This will give you visual access to the DFI on the left side of the base unit. Press reset to make certain the blue light is not flashing. Take your phone or devices camera and point it at the clear plastic shield right under the safety bar on the left side of the base, you ...If, after three attempts, the unit is unable to cycle, the Globe will stop and the Control Panel will flash yellow then red lights. You will also receive a notifcation on your phone if you use...

When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second.If the timing light is solid red, this indicates the cat sensor has been activated by a cat entering the globe. Once the cat exits, the cycle delay countdown to a Clean cycle will begin. ... If your Litter-Robot is flashing red or stuck upside down, complete the troubleshooting steps in our Litter-Robot 3: Red light flashing (Cat sensor fault ...The Litter-Robot is ready for use when the Globe is at the Home position and the blue light on the Control Panel is on. x When a cat enters the Globe, the Cat Sensor is activated; the blue light turns off and the red light turns on. x Once the cat exits the Globe, the countdown to a Clean cycle begins. When the Wait Time (see page 23) hasThe Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...These sensors detect when a cat has entered or exited the unit. If your unit has a flashing red light bar or the unit will not cycle, this indicates that the cat sensor has been triggered for more than 30 minutes. Successful: If your unit returned home and displays a blue light bar, you've been successful.

If your Litter-Robot 3 is not powering on, there are several things we need to check. Ensure Litter-Robot is plugged directly into a wall outlet. We do not recommend using an extension cord or power strip. Unplug the power supply from the wall. Confirm that your outlet is working by testing it with a known working device, such as a lamp or cell ...Got a litter robot about 2 months ago, not had any issues with it so far. This week it's started to not recognise when there is a cat in there (timing light not flashing red for example) and we have to manually press the cycle button. Any ideas why this might be happening. I've already pressed the reset button and turned it off/on at wall ...Cleaned out litter in the globe grooves, just in case; Made sure cat sensor connection on the bottom was good to go (reseated, checked for issues); Removed globe and dirty litter drawer, shorted bonnet pins, cycled LR3; First time, it did the same thing (ran for a little, stopped, went back and did yellow-red seq);…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. 1. Press the power button to turn the unit o. Possible cause: ibobey June 23, 2021, 8:56pm 26. hello there seems to be a short circuit between the .